Swiftech H20 120 T Manuale Utente

HH2200--112200TT TThheerrmmooeelleeccttrriicc LLIIQQUUIIDD CCOOOOLLIINNGG KKIITTSS TUTORIAL & INSTALLATION GUIDE

Packing list MCR120 radiator 1 ½” barbs 2 Snap-rivet 4 120x25mm fan 1 6-32” x 3/8” Philips screw 4 #6 worm drive clamps 2 FrontofChassisSnap-

Parts QTY PARTS QTY MCB-120™ Housing assembly 1 ½” barbs 2 Retention hardware (screws, etc.) 1 # 6 worm drive clamps 6 (*) ½” copper tube

1. General Use The MCP650 pump is a magnetically driven centrifugal pump featuring a 12 V DC motor. It requires no maintenance when used with de-min

4. Performance & Specifications Nominal voltage 12 V DC Operating voltage range 6 to 14 VDC Nominal power (@ 12 V) 24 W Nominal current (@ 1

PARTS LIST – BARBED ADAPTERS ARE SOLD SEPARATELY Parts QTY PARTS QTY MCRES-525™ Reservoir 1 Retention screws 4 Fill-cap & o-ring 1 Port pl

Installation guidelines Figure 1: Always leave sufficient slack in the lines to pull enough of the reservoir out of the drive bay and uncover th

S320-12 This kit includes (Check-marked for applicable model and content): Qty Item 1 S320-12 power supply installed in 5 ¼” adapter tray, screws 1

2. Relay Switch Installation  Find a suitable placement to drill a hole for the A/C socket adapter. Leave sufficient room under or above the hole

The template below provides holes dimensions for installation of such 80mm fan blowhole. A fan guard and snap rivets are provided with the kit to co

Part Qty Part Qty MCW5002-775T assy. with TEC and gaskets 1 Céramique thermal compound 1 3/8” NPT to ½” barb fittings 2 Euro-style connector

Packing List Included components per applicable model: H20-120-PT □ H20-120-775T □ H20-120-64T □ H20-120-AT □ Description Product Code Description

1. Preparing the motherboard Remove the stock heatsink retention mechanism to reveal the four-motherboard mounting holes. Install a standoff in ea

and remove the masking tape. Then let the board dry completely per manufacturer specs. b. CPU preparation & water-block installation Dielectri

 The TEC module is provided with “bare wires” to facilitate installation with screw type terminals such as featured in the S320-12 power supply 

Part Qty Part Qty MCW5002-PT assy with TEC and gaskets 1 Arctic Alumina thermal compound 1 3/8” NPT to ½” barb fittings 2 Euro-style connec

1. Preparing the motherboard Remove the stock heatsink retention frame (the black plastic frame that clips down to your motherboard). This will r

• Dielectric grease application: This step will ensure that condensation does not form inside of the CPU socket. Procure a tube of dielectric

IMPORTANT WARNING: Solder joints of the wires to the thermoelectric module are extremely fragile. Bending the wires at their root will break the s

 Type of Coolant:  For best performance, use 95% distilled water, and 5% Swiftech brand “HydrX” corrosion inhibitor (available here: http://www

Part Qty Part Qty MCW5002-AT assy with TEC and gaskets 1 Arctic Alumina thermal compound 1 3/8” NPT to ½” barb fittings 2 Euro-style connec

1. Condensation control measures The following instructions are crucial to long lasting & reliable operations. Do not skip these steps, and d

TTaabbllee ooff ccoonntteennttss I. TUBE ROUTING ...

Figure 4 Figure 5 Squirt a generous amount of grease onto the socket. Force the grease inside of the pin-holes with your finger. Make sure that t

Figure 8 Installation of the cooler to the motherboard is now complete! 2. Electrical Installation IMPORTANT WARNING: Solder joints of the wir

b. Connecting to your computer power supply: Important Warning: to connect the MCW5002-ATcooler to an ATX computer power supply, you must carefull

Part Qty Part Qty MCW5002-64T assy with TEC and gaskets 1 Arctic Alumina thermal compound 1 3/8” NPT to ½” barb fittings 2 Euro-style conn

1. Condensation control measures The following instructions are crucial to long lasting & reliable operations. Do not skip these steps, and do

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Rouchon Industries, Inc., dbA Swiftech™ – 1703 E. 28th St, signal Hill, CA 90755, USA – T (562) 595-8009 – F (562) 595-8769 – All content Copyright S

Preamble Congratulations on your purchase of a Swiftech liquid cooling system! This kit has been designed to facilitate the installation of the com

I. TUBE ROUTING The following table contains examples on how to establish connections between the different elements of a cooling circuit This table

Cutting the tubing, & connecting components Now that your mock-up installation is in place, it is time to cut segments of tubing and connect the d

Figure 1 Figure 1 above illustrates a typical CPU cooling installation. Notice the use of Coolsleeves in very tight bends to prevent the tubes from k

III. Draining the system  You will need to disconnect a line from one of the lowermost components. Procure a bucket large enough to receive approx

V. Appendix: Individual Component Installation guides - INTENTIONNALY LEFT BLANK - Rouchon Industries, Inc., dbA Swi