Swiftech H20 220 T Manuale Utente

Copyright Swiftech 2005 – All rights reserved – Last revision date: 12-27-05 - Information subject to change without notice – URL: http://www.swi

2. MCW5002-PT™ THERMOELECTRIC WATER-BLOCK INSTALLATION GUIDE FOR INTEL PENTIUM 4 (SOCKET 478) Figure 1 A. Preparing the Motherboard Copyrig

Use a ¼” socket tool to drive the standoff, and a small pair of pliers to prevent the locknut from spinning. Torque value should not to exceed 16 in

To complete the condensation prevention measures, simply apply the neoprene sticker provided with your MCW5002-PT accessories to the back of the moth

3. MCW5002-AT™ THERMOELECTRIC WATERBLOCK INSTALLATION GUIDE FOR AMD ATHLON MP, XP, SEMPRON (SOCKET 462 MOTHERBOARDS WITH MOUNTING HOLES EXCLUSIVELY

Figure 2 Figure 3 Spray the back of the motherboard, concentrating on the area immediately behind the CPU. Also spray all the way down, in a vertica

Figure 6 Remove the peel-off paper back from the motherboard gasket, and install it as shown above. The sticky side should be towards the motherboard

4. MCW5002-64T™ THERMOELECTRIC WATER-BLOCK INSTALLATION GUIDE FOR AMD ATHLON 64, OPTERON (SOCKET 754, 939, 940) Figure 1 Preamble The followi

Figure 2 Figure 3 Spray the back of the motherboard, concentrating on the area immediately behind the CPU. Also spray all the way down, in a vertica

Part # AJ00264 backing plate alone Part # AJ00172 complete retention frame & backing plate Figure 6 Figure 7 Remove the peel-off paper back

 Type of Coolant:  For best performance, use 5 to 10% of Swiftech brand “HydrX” corrosion inhibitor mixed with distilled water only .  Regular

Packing List Included components check-marked per applicable model: H20-220-PT □ H20-220-775T □ H20-220-64T □ H20-220-AT □ Description Product Code

Figure 1 B. Relay Switch Installation Copyright Swiftech 2005 – All rights reserved – Last revision date: 12-27-05 - Information subject to change

ENLGround + 12vRelay switch connection diagramN\O+A/C Soc ketS3 2 0 - 1 2Po w e r su p p l yComputerPo w e r Su p p lyRe l a y swi t c hWARNING! Alw

Copyright Swiftech 2005 – All rights reserved – Last revision date: 12-27-05 - Information subject to change without notice – URL: http://www.swiftnet

Another example of “blow-hole” installation Now that your power supply is physically in place, let’s move on to the installation of the next compon

o Exit cables and connectors from various PCI devices: the Radbox base plate can be moved in both vertical and horizontal directions to allow clearan

Remove the radiator assembly from the back-plate and mark the center of the circle. Two rubber grommets are provided with your kit so that you can r

Example of Installation of the MCR220-QP radiator with Radbox 3. RE-INSTALLING THE MOTHERBOARD/WATER-BLOCK ASSEMBLY INTO THE CHASSIS Once your

4. MCP655 PUMP INSTALLATION Copyright Swiftech 2005 – All rights reserved – Last revision date: 12-27-05 - Information subject to change without noti

Copyright Swiftech 2005 – All rights reserved – Last revision date: 12-27-05 - Information subject to change without notice – URL: http://www

5. MCRES-MICRO RESERVOIR INSTALLATION ITEMNO.PART NUMBER DESCRIPTION QTY.1 MCRES-MICRO Reservoir 121-4“ NPSM x 3-8“ and 1-2“barbBarb fitting2 pairse

TABLE OF CONTENTS I. Motherboard preparation & water-block mechanical installation...

 Two mounting methods can be used o Permanent mount with the provided mounting hardware as shown in figure 1. Three holes will need to be drilled

Reservoir discharge to pump inlet Pump discharge to Radiator inlet Radiator discharge to CPU Water-block inlet CPU Water-block discharge to reservoir

 The TEC module is provided with “bare wires” to facilitate installation with screw type terminals such as featured in the S320-12 power supply  C

III. Periodic maintenance...

Preamble Congratulations on your purchase of a Swiftech liquid cooling system! This kit has been designed to facilitate the installation of the comp

Installation Overview The following is a typical sequence of components installation. Step 1 is always first. Steps 2 to 6 may be performed out of se

1. MCW5002-775T™ THERMOELECTRIC WATER-BLOCK INSTALLATION GUIDE FOR INTEL PENTIUM 4 (LGA775) Figure 1 A. Preparing the motherboard Remove th

The following instructions are crucial to long lasting & reliable operations. Do not skip these steps, and do not take shortcuts. Permanent dama

Step 4 Step 5 Step 6 7/ Squeeze a small amount of Céramique thermal compound on the CPU. 8/ Peel-off the protective paper from motherboard gasket #2